Polyurethane Foam Sealant in Construction Insulation
Model: K90
Product Introduction
The single-component polyurethane foam sealant material is particularly suitable for applications in the building sector for insulation and installation. It is applicable for bonding, fixation, installation, sound insulation, heat insulation, sealing against moisture, gas isolation, filling the gaps in structures, engineering holes and various cracked seams, etc.
Product Features
1. Optimal operating temperature for the project: 18 - 25 degrees Celsius
2. Normal applicable temperature for the material tank: 5 - 35 degrees Celsius
3. Storage temperature: ±25 degrees Celsius
4. The foam can adhere to concrete, walls, wood and plastic surfaces, but not to silicone resins and Teflon.
5. The temperature range after curing is -30 to +80 degrees Celsius.
6. The product is harmless to the human body after curing.
Scope of Use
1. Insulation and sealing of door and window frames
2. Installation sealing and leak prevention of various pipes
3. Waterproofing and insulation of walls and roofs
4. Sealing and sealing of air conditioners
5. Installation positioning and insulation of various electrical switch boxes
6. Shock-proof packaging of various non-standard fragile items
7. Filling and leak repair of hot water tanks, bathtubs and their surroundings
8. Filling of various wall gaps
9. Sealing and repair for various buildings

Construction Notes
1. Before construction, remove dust and oil stains from the construction surface and spray a little water on it.
2. When filling vertical gaps, fill from bottom to top (note the expansion performance of the foam).
3. The flow of the foam can be adjusted by controlling the trigger.
4. The foam can be cleaned with a special cleaning agent before it cures.
5. The demolding time of the foam surface is 10 minutes. The foam can be cut after 20 minutes and will cure in about one hour, and reach stability within 3-5 hours (all data obtained under laboratory conditions).
6. This product does not release ultraviolet rays, so it is recommended to apply coatings of other materials on the cured foam surface (such as cement mortar, paint, etc.).
Usage Method
1. Shake the material can up and down for one minute before use.
2. Clean and moisten the construction surface before application.
3. Invert the material can and connect it to the spray gun. Open the flow valve by turning it counterclockwise.
4. Spray from bottom to top. Spray until the volume reaches half of the required filling volume.
5. The foam will start to cure after ten minutes. Wait for one hour before proceeding to the next step.
6. Excess cured foam can be removed with a scraper. The surface can be treated with cement, mortar, paint or silicone.
Safety Instructions
1. Keep away from direct sunlight and store in a cool and dry place with a temperature not exceeding +50 degrees Celsius.
2. Do not burn or puncture the empty can after use.
3. Keep away from open flames and do not come into contact with flammable and explosive products.
4. This product may produce flammable mixed gases during use. Therefore, the construction site should have good ventilation; construction workers should wear construction gloves and goggles during construction and should not smoke.
5. This product has strong adhesion when not cured and is penetrative to fabric fibers. Do not touch your clothes during use.
6. Keep the material can out of reach of children. If the foam agent comes into contact with the eyes, rinse with clean water or seek medical advice. If it comes.
| Capacity | 900g |
| Storage condition | Store in the original sealed condition at a cool and dry place with a temperature below 5-27 degrees. The shelf life is 12 months. |
| Standard | JC936-2004 |
| Surface curing time | 8-10 minutes |
| Complete curing time | At a temperature of 10-40 degrees and a relative humidity of 40%-80%, the complete curing time is about 80 minutes. |
Storage

Packag

Color

exhibition

mode of transportation

Hot Tags: polyurethane foam sealant in construction insulation, China polyurethane foam sealant in construction insulation manufacturers, suppliers, factory, Polyurethane Foam Sealant in Construction Insulation, Polyurethane foam sealant for filling the voids, Polyurethane foam sealant in agricultural applications, Polyurethane foam sealant for garden landscaping, Polyurethane foam sealant for flooring, polyurethane foam filler
You Might Also Like
Send Inquiry









